If door is opened during fill cycle, fill will stop. When filled, pump turns on for 10 seconds. FILL lit and sump temperature displayed when machine is filling. DISPLAY SHOWS REMARKS Dishwasher performs self-check. OPERATING THE LXi DISHWASHER DO THIS Press ON. If 8.40% sodium hypochlorite solution is to be used, contact your local Hobart Service Office. On model LXiC only, the chemical sanitizer pump is factory-set for use with 6% sodium hypochlorite solution. Therefore, chemical-sanitizing dishwashers should not be used to wash such items. HOLE FOR 1" TRADE.ĬHEMICAL SANITIZER (LXiC AND LXiGC) CAUTION: Items such as pewter, aluminum and silver will be attacked by sodium hypochlorite (bleach). CONNECTION INFORMATION (AFF = ABOVE FINISHED FLOOR) LEGEND E1 ELECTRICAL CONNECTION: 1-3/8" DIA. IMPORTANT: THE SODIUM HYPOCHLORITE (LIQUID BLEACH) CONTAINER SHOULD BE PLACED NO HIGHER THAN 10" ABOVE FLOOR. IF PRESSURES HIGHER THAN 25 PSIG ARE PRESENT, A PRESSURE REGULATING VALVE MUST BE INSTALLED IN THE WATER LINE TO THE GLASSWASHER (BY OTHERS). WARNING: REQUIRED FLOWING WATER PRESSURE TO THE GLASSWASHER IS 20 ± 5 PSIG. IF PRESSURES HIGHER THAN 25 PSIG ARE PRESENT, A PRESSURE REGULATING VALVE MUST BE INSTALLED IN THE WATER LINE TO THE DISHMACHINE (BY OTHERS). WARNING: REQUIRED FLOWING WATER PRESSURE TO THE DISHMACHINE IS 20 ± 5 PSIG. Disabling this feature will eliminate the alarm activation if no chemical is sensed. The Detergent and/or Rinse Aid pumps can be turned off by entering this programming mode. This includes the Detergent and Rinse Aid pumps, but does not apply to the Sanitizer pump on the LXiC and LXiGC models. OPERATOR PROGRAMMING MODE The Operator Programming mode allows changes to be made from factory settings to the chemical pumps’ operation.
Install 1" trade conduit and fitting to the cover plate. 2) securing the controls drawer and open it fully. A hole for 1" trade size conduit is supplied in the cover plate. Remove the cover plate at the upper right in the back of the machine (Fig. Model Minimum Supply Circuit Conductor Ampacity Maximum Protective.Ĭonnection Method 1.
NOTE: For supply connections, use copper wire only rated at 90☌ minimum.
ELECTRICAL DATA Complied in accordance with the National Electrical Code NFPA-70, latest addition. WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
This "flush-out" is necessary to remove all.ĮLECTRICAL CONNECTION WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. The plumber connecting this machine is responsible for making certain that water lines are THOROUGHLY FLUSHED OUT BEFORE connecting to the dishwasher. Higher hardness may cause excessive formation of lime scale. Water Supply A water hammer arrestor (meeting ASSE-1010 Standard or equivalent) should be installed (supplied by others) in the common water supply line at the service connection. Steam generated from normal operation may escape from the door. LOCATION Prior to installation, verify that the electrical supply agrees with the specifications on the machine data plate, which is located on the top of the door. If this machine is found to be damaged, save packaging material and contact the carrier within 15 days of delivery. INSTALLATION UNPACKING Immediately after unpacking the dishwasher, check for possible shipping damage. Standard equipment includes two 20" x 20" racks, electronic controls. All LXiH and LXiGH dishwashers include Sense-A-TempTM to insure proper hot water temperature during rinse.
All LXi Series dishwashers shut down automatically 4 hours after last use to conserve energy. Installation, Operation and Care of LXi SERIES DISHWASHERS SAVE THESE INSTRUCTIONS GENERAL The LXi Series dishwashers are fully automatic, front-loading dishwashing machines that are capable of 30 racks per hour. I N S T LXi SERIES DISHWASHER R U C T I O N S LXi SERIES DISHWASHER MODELS LXiC LXiH LXiGC LXiGH ML-130016 ML-130017 ML-130018 ML-130019 701 S.